Analog Oscilloscopes

100MHz - Delayed Sweep

Model S-1390

Delayed Sweep & Dual Trace

Features

	1mV/DIV Sensitivity.
	Sweep to 2ns/DIV
	Z Axis Input.
	Single Sweep.
	Dust Cover Included.
	2 Free x1, x10 Probes

Specifications

Vertical Amplifiers (CH 1 and CH 2) Horixontal Amplifier (continued)

Sensitivity: 5mV/div - 5V/div (x1 mode).
                  1mV/div - 1V/div (x5 mode).
Attenuator: 1-2-5 sequence, 10 step attenuator plus   vernier control.
Rise Time: 5.8ns (S-1360), 3.5ns (S-1390).
Over Shoot: Less than 5%.
Input Impedance: 1MΩ ±2%, 25pF ±10%.
Max Input Voltage: 400V (DC + AC peak).
Operating Modes: CH1, CH2, DUAL(ALT or CHOP) and ADD.
Chop Frequency: Approximately 500kHz.
Algebraic Addition: CH 1 + CH 2, CH 1 - CH 2.
Inverter: CH 2 only.
Polarity Reversal: CH 2 only Bandwidth: DC - 1MHz(-3dB).
X-Y Phase Difference: Approximately 3° at 50kHz.

Horizontal Amplifier Sweep System

X-Y Mode: Switch selectable using X-Y switch
          CH 1: X axis.
          CH 2: Y axis.
Accuracy: Y axis±3%, X axis±6% Sweep Display Mode: Main, Mix, Delay
Hold Off Time: 5:1 continuously variable (0.1µs/div).

Main Sweep

Sweep Speed:
S-1360: 0.1µs/div - 2s/div in 1-2-5 sequence, 23 steps
S-1390: 20ns/div - 0.5s/div in 1-2-5 sequence, 23 steps
Accuracy: ±3%
Variable Time Control: 5:1, uncalibrated, continuously variable between steps.
Sweep Magnification:
10X, ±10%, extend sweep speed up to 10ns/div (S-1360).
10X, ±10%, extend sweep speed up to 2ns/div (S-1390).

Delayed Sweep Component Tester (S-1360 only)

Sweep Speed:
S-1360: 0.1µs/div - 2s/div in 1-2-5 sequence, 23 steps.
S-1390: 20ns/div - 0.5s/div in 1-2-5 sequence, 23 steps.
Acccuracy: ±3%
Delay Time Position: Varaiable control to locate desirable waveform for extending. Test Voltage: Max. 6Vms (open circuit).
Test Current: Max. 11mA (shorted).
Test Frequency: Line Frequency.
Components: Capacitor, Inductor, Diode, Transistor, Zener etc.

Trigger CH 2 Output

Trigger Coupling: AUTO, NORM, TV-V, TV-H (S-1360).
AC, TV-V, TV-H, LINE (S-1390)
Trigger Source: CH 1, CH2, ALT (V MODE), LINE, EXT.
Slope: ± Output Level: 100mV/DIV (no load). 50mv/div (50Ω load).
Bandwidth: 20Hz - 20MHz (-3dB).

Trigger Sensitivity (S-1360/S-1390) Other Specifications

Coupling Bandwidth Internal External CRT: Type: Rectangular with internal graticule.
        Display Area: 8 x 10 div (1div = 1 cm).
        Accelerating Voltage: 12kV (S-1360), 14kV (S-1390).
        Phosphor: P31
Z Modulation: Positive TTL signal, low level blank intensity at any intensity, high level unblank any intensity.
Trace Rotation: Adjustable front panel.
Calibrator: Square wave 1kHz, 2.0Vpp±3% (S-1360)
                Square wave 1kHz, 0.5Vpp (S-1390)
Power requirements: 115, 230VAC±10%, 50/60Hz.
Power Consumption: Approximately 55 watts
Dimensions: 5 1/4" (H) x 12 3/4" (W) x 15 5/8" (D).
New Weight: S-1360: 17.2lbs (7.8kgs) S-1390: 18.7lbs (8.5kgs).
Accessories Supplied: Two x1, x10 probes, schematic diagram & parts list, AC power cord, spare fuse and dust cover.

TV-V DC- 1kHz 1.0 div 0.1Vpp

TV-H 1kHz - 100kHz 1.0 div 0.1Vpp

AUTO 100Hz -60/100MHz 1.5/2.0 div 0.1/0.2Vpp

NORM 100Hz -60/100MHz 1.5/2.0 div 0.1/0.2Vpp

Specifications
Vertical Amplifiers (CH 1 and CH 2)	Horixontal Amplifier (continued)
Sensitivity: 5mV/div - 5V/div (x1 mode). 1mV/div - 1V/div (x5 mode). Attenuator: 1-2-5 sequence, 10 step attenuator plus vernier control. Rise Time: 5.8ns (S-1360), 3.5ns (S-1390). Over Shoot: Less than 5%. Input Impedance: 1MΩ ±2%, 25pF ±10%. Max Input Voltage: 400V (DC + AC peak). Operating Modes: CH1, CH2, DUAL(ALT or CHOP) and ADD. Chop Frequency: Approximately 500kHz. Algebraic Addition: CH 1 + CH 2, CH 1 - CH 2. Inverter: CH 2 only. Polarity Reversal: CH 2 only	Bandwidth: DC - 1MHz(-3dB). X-Y Phase Difference: Approximately 3° at 50kHz.
Horizontal Amplifier	Sweep System
X-Y Mode: Switch selectable using X-Y switch CH 1: X axis. CH 2: Y axis. Accuracy: Y axis±3%, X axis±6%	Sweep Display Mode: Main, Mix, Delay Hold Off Time: 5:1 continuously variable (0.1µs/div).
	Main Sweep
	Sweep Speed: S-1360: 0.1µs/div - 2s/div in 1-2-5 sequence, 23 steps S-1390: 20ns/div - 0.5s/div in 1-2-5 sequence, 23 steps Accuracy: ±3% Variable Time Control: 5:1, uncalibrated, continuously variable between steps. Sweep Magnification: 10X, ±10%, extend sweep speed up to 10ns/div (S-1360). 10X, ±10%, extend sweep speed up to 2ns/div (S-1390).

Delayed Sweep				Component Tester (S-1360 only)
Sweep Speed: S-1360: 0.1µs/div - 2s/div in 1-2-5 sequence, 23 steps. S-1390: 20ns/div - 0.5s/div in 1-2-5 sequence, 23 steps. Acccuracy: ±3% Delay Time Position: Varaiable control to locate desirable waveform for extending.				Test Voltage: Max. 6Vms (open circuit). Test Current: Max. 11mA (shorted). Test Frequency: Line Frequency. Components: Capacitor, Inductor, Diode, Transistor, Zener etc.
Trigger				CH 2 Output
Trigger Coupling: AUTO, NORM, TV-V, TV-H (S-1360). AC, TV-V, TV-H, LINE (S-1390) Trigger Source: CH 1, CH2, ALT (V MODE), LINE, EXT. Slope: ±				Output Level: 100mV/DIV (no load). 50mv/div (50Ω load). Bandwidth: 20Hz - 20MHz (-3dB).
Trigger Sensitivity (S-1360/S-1390)				Other Specifications
Coupling	Bandwidth	Internal	External	CRT: Type: Rectangular with internal graticule. Display Area: 8 x 10 div (1div = 1 cm). Accelerating Voltage: 12kV (S-1360), 14kV (S-1390). Phosphor: P31 Z Modulation: Positive TTL signal, low level blank intensity at any intensity, high level unblank any intensity. Trace Rotation: Adjustable front panel. Calibrator: Square wave 1kHz, 2.0Vpp±3% (S-1360) Square wave 1kHz, 0.5Vpp (S-1390) Power requirements: 115, 230VAC±10%, 50/60Hz. Power Consumption: Approximately 55 watts Dimensions: 5 1/4" (H) x 12 3/4" (W) x 15 5/8" (D). New Weight: S-1360: 17.2lbs (7.8kgs) S-1390: 18.7lbs (8.5kgs). Accessories Supplied: Two x1, x10 probes, schematic diagram & parts list, AC power cord, spare fuse and dust cover.
TV-V	DC- 1kHz	1.0 div	0.1Vpp
TV-H	1kHz - 100kHz	1.0 div	0.1Vpp
AUTO	100Hz -60/100MHz	1.5/2.0 div	0.1/0.2Vpp
NORM	100Hz -60/100MHz	1.5/2.0 div	0.1/0.2Vpp